• Compatible with NXP 64-bit e5500 core which supports the PowerPC V2.06 instruction set . The processor core has three privilege levels according to the instruction set: user, supervisor, hypervisor

• Dual-core architecture, with each core enjoying exclusive access to 32KB L1 ICache, 32KB L1 DCache, and 256KB L2 Cache

• Supporting a maximum physical memory space of 64 GB , with big/little-endian access per page

• Supporting external tamper detection for bootloader

• Security fuse module

• Security monitoring module

• Internal and external code signature

• Data secure storage:

- Unique Blob mechanism for secure storage of sensitive data in off-chip Flash

- Mechanism for destroying sensitive data within the chip in the event of a security violation

- Supporting a rich set of physical attack defense mechanisms

• Built-in multi-core public key, symmetric, and hash algorithm units, random number generator

- True random number engine with 4 independent clocks

- Symmetric algorithm acceleration engine: SM4/AES/DES/3DES

- Digest algorithm acceleration engine:
SHA0/SHA1/SHA224/SHA256/
SHA384/SHA512/SM3/MD5/HMAC

- Public key algorithm acceleration engine (PKHA):
SM2/SM9/RSA(4096bit)/DH(4096bit)/ ECC(1024bit)

• Supporting 2 chip selects, DDR4 devices ranging from 64Mbit to 8Gbit

• Programmable settings to meet all SDRAM timing parameters

• Supporting partial array self-refresh

• Supporting double-bit error detection and single-bit error correction ECC

• Automatic DRAM initialization sequence or by software

• Supporting a maximum of 4 PCI-E3.0 controllers by configuration, with output data rates of 8Gbps, 5Gbps, and 2.5Gbps

• Supporting 2 SATA3.0 controllers by configuration, with output data rates of 6Gbps, 3Gbps, and 1.5Gbps

• Supporting 4 Gigabit Ethernet controllers with SGMII output b configuration, supporting up to 4 SGMII interfaces for Gigabit

• Supporting 1 10 Gigabit Ethernet (based on the 10GBASE-R protocol) after configuration

• Compatible with the version 3.0 of PCI-Express Base Specification, backward compatible with 2.0 and 1.1

• Supporting Root Complex (RC) and Endpoint (EP) configurations

• Each supporting x4, x2, and x1 link widths

• Supporting 32-bit and 64-bit addressing and payload sizes up to 256 bytes

• Supporting PCI-Express messaging and interrupts

• 2 SATA3.0 controllers supporting 1.5Gbps, 3.0 Gbps, and 6Gbps operations

• Supporting high-speed descriptor-based DMA

• Supporting Native Command Queuing (NCQ) commands

• Supporting hot swapping, including asynchronous signal recovery

• Host/Device configurable

• Supporting OTG function

• Supporting 6 CAN2.0B interfaces

• Supporting CAN2.0B technical specifications

• Complied with the version 3.0 of SD Host Controller Standard Specification

• Compatible with the version 4.5 of MMC System Specification

• Compatible with the version 3.01 of SD Memory Card Specification and supporting high-capacity SD memory cards

• Compatible with the version 3.0 of SDIO Card Specification

• Interface includes SPI_MOSI, SPI_MISO, SPI_CLK, and 4 chip selects

• Supporting eSPI hosts

• Arbitration lost interrupt, automatic mode switching, switching from master mode to slave mode

• Four UART controllers (2 UART interfaces on the chip)

• Full-duplex operation

• Software-selectable serial interface data format

• All ports can be configured as open-drain drivers

• All ports can optionally generate interrupts when their states change

• Pin function multiplexing between NAND/NOR and GPCM

• Supporting memory banks with capacities up to 4 GB (for NOR and GPCM)

• LCD Interface

• Two 8-channel DMA engines

• SRAM :512KB

• Power domains: 0.8V, 1.2V, 1.8V, 3.3V

• Packaging: FC-PBGA780（23mm * 23mm）